Welcome, visitor! [ Register | Loginrss

 

$220,000

2009 Keith Huber Beringer II

Description

We are pleased to quote on the BERRINGER INDUSTRIAL WET/DRY VACUUM LOADER mounted on a 2009 Peterbilt 340 chassis with 5,158 miles and 239 hours, EQ# 3840 , with the following specifications:

QUANTITY:
One

TANK CAPACITY:
The total tank capacity is 3,300 gallons. A primary shut-off system with a 6” stainless steel float ball and buna seat are located in the front top center of the tank. A liquid level indicator with stainless steel one-piece shaft and 8” stainless steel float ball are provided in the rear head with an exterior indicator arrow. The liquid level assembly includes a quad seal bushing with viton o-ring seal and is replaceable from the outside of the tank. Baffle assemblies are bolted in place to protect against anti-surge of liquid or slurry when transporting. Large top and bottom clearance is provided for easy flow of product with unloading. An automatic pressure valve is provided on the tank and set to the tank design pressure.

TANK MATERIAL:
The tank is constructed with carbon steel and is rated for continuous maximum vacuum operation and 15 psi working pressure. All horizontal and longitudinal seams are submerge arc welded.

CODE TYPE:
The tank is built and stamped in accordance with section VII of the ASME (American Society of Mechanical Engineers) boiler code. This is a prerequisite before it can be in accordance with the US Department of Transportation for hauling hazardous materials on the highway. This tank is built in accordance with the US Department of Transportation specification DOT412. A plaque must be attached to the tank which displays data of compliance to this specification. Additional components including self closing discharge valve(s), roll-over protection, increased pressure relief system, isolation valve(s), complete rear valve protection and placards are required and included.

NUMBER OF COMPARTMENTS:
The tank is a single compartment type.

TOP MANWAYS:
The tank is equipped with one top 20” manway which includes an access ladder and non-skid platform. An o-ring seal is matched to a dome cover lid with four (4) easy opening fasteners. The cover dome is equipped with a handle and rest pad for safe opening and closing of the hatch. The top manway is located in the debris tank.

REAR HEAD TYPE:
The rear head is ASME flanged and dished type, hinged at the top with 1 ½” diameter bronze oil-lite bushings and sealed with a 1 ½” neoprene rubber gasket. The full opening rear head opens by gravity when the tank is raised. Forged “T” bolt wing nut type head. One rear 6” nozzle and one rear 4” nozzle are flanged with bolted piston type valves and dust caps. The 4” nozzle includes an internal standpipe with exit elbow that terminates at the top of the tank. A 30/30 liquid filled vacuum/pressure gauge is located at the upper rear portion of the tank and registers the “inches of mercury” (Hg) or “pounds per square inch (PSI) inside the debrs tank.

HYDRAULIC TANK LIFT:
A three (3) stage double acting hydraulic cylinder is mounted to the front head to lift the tank and provides an automatic lock when the tank is in the lowered transport position. Trunions installed on each side of the lift cylinder include grease zerks for periodic lubrication. The tank hinges at the rear on two solid bar pins. The hydraulic lift cylinder requires hydraulic power to raise or lower the tank.

VACUUM PUMP POWER SOURCE:
Power to run the vacuum pump is provided through Splitter Transfer Case which is mounted in line with the truck chassis main driveline.

VACUUM PUMP COOLING OR TYPE:
The vacuum pump is a liquid ring type with high CFM, high vacuum and VRT (Vapor Reduction Technology). No internal oil is required and cooling is accomplished through the service liquid used and direct inlet cooling chambers.

VACUUM PUMP CFM:
1,600 CFM free air; 1,595 cfm @ 18” Hg; 27-29” Hg maximum.

VACUUM PUMP DRIVE:
The vacuum pump is driven by a belt-drive system which receives power from a transmission mounted power take-off.

WATER PUMP GPM:
High Pressure Water is not included in this specification.

WATER PUMP PSI:
High Pressure Water is not included in this specification.

WATER PUM DRIVE:
High Pressure Water is not included in this specification.0

INSTALLATION:
Complete system installed on a 2009 Peterbilt Model 340 Chassis,
VIN# 2NPRLN0X39M782473

Ad Reference ID: N/A

Leave a Reply

Item Location

To inquire about this ad listing, complete the form below to send a message to the ad poster.

Information about the ad poster

  • Listed by: mrenner
  • Member Since: January 25, 2010

Other items listed by mrenner

View all ads by mrenner »