Welcome, visitor! [ Register | Loginrss

 

$Call for Quote

2007 Mud Dog

Description

One (1) Work Ready SuperProducts Mud Dog Hydro-Excavator Unit, EQ# 3148, S/N 072240510, mounted on a 2007 Sterling Chassis, VIN# 2FZHAZDEX7AW79853 with the following features:

Debris Tank/Collector Body

Debris tank shall have a minimum total usable volume of ten (10) cu. yds. (7.6 m3), 2000 gallon water capacity (7,570 L), cylindrical shaped, and constructed from 0.25″ (6.0 mm) A36 steel including the rolled cylinder and front tank head.
Debris tank is emptied via ejector plate unloading. A full diameter, hydraulically operated ejector plate ejects the collected material from the debris body.
The rear door to be full diameter and opened with double acting hydraulic cylinders for power open and close. The door to open 90 degrees to allow easy access to the debris body interior.
Splash shield around lower two thirds of rear tailgate.
Controls for latching/unlatching, opening/closing the tailgate , and extending/retracting the ejector plate must be located on the driver’s side and forward of the debris tank.
Two (2) worklights mounted on rear of unit. Switched in truck cab.
The rear door seal must be self compensating type and mounted on the door to increase seal life.
A full diameter, rear opening tailgate, top hinged, with flat construction shall be provided, fabricated of 0.25″ (6.0 mm) steel plate, and fitted with a full diameter “B” shaped neoprene gasket to ensure a water tight seal.
Five (5) Hydraulic wedge type latches shall be provided on the rear tailgate for holding the door closed.
Flashing arrow board on rear of unit. Controlled in truck cab.
To prevent overfilling by liquids of the collector body, two (2) 9″ dia. (228.6 mm) stainless steel float balls will be provided to act as the primary stage to prevent debris from reaching the vacuum pump.
Toolbox located directly behind chassis cab. Toolbox to be 18” x 48” x 60”.
A 6″ dia. (152.4 mm) right side body mounted drain will be provided with a
knifegate valve to remove water from the front of the collector body. A 6″ x 10′ (152.4 mm x 3.05 m) lay flat drain hose will be provided.

Vacuum System – 28” Hg
A positive displacement trilobe vacuum pump rated at 6000CFM and 28”hg., driven from the single chassis engine via a heavy duty Cotta transfer case mounted between the rear axle and the truck transmission.
A steel cover will shield the drive shaft between the vacuum pump and transfer case.
To engage and disengage the vacuum pump, a floor mounted mechanical lever and cable, connected to the transfer case, will be operated from inside the cab.
To reduce the dba level, a heavy-duty exhaust silencer, with a top mounted rain cap, shall be mounted to the vacuum pump.
To achieve the second stage filtration level, a tapered cyclone separator will be installed between the collector body vacuum outlet and the vacuum pump. A rectangular storage area with a clean-out cover and a liquid drain valve shall be located at the bottom of the tapered cone.
Third stage filtration will be achieved by providing a pleated filter capable of containing particles sized 10 micron or larger. The filter shall be removed for easy cleaning or replacement.
To allow the operator the convenience of shutting the vacuum off and on at the inlet tube without disengaging the vacuum pump, a vacuum relief vent door shall be included and operable from the portable pendant or cabinet control panel.

Boom System

An 8″ dia. (203.2 mm) heavy duty vacuum hose and boom assembly shall be provided and mounted on top of the forward part of the collector body.
The boom assembly shall be stored at the right front corner of the chassis for transport.
A cradle shall also be provided to support the boom during transport.
All boom functions (up/down/left/right/in/out) shall be hydraulic powered and controlled at the portable pendant, and furnished with 50′ of heavy duty electrical cord. Back up controls for the boom functions shall be provided inside the primary storage cabinet.
The boom tower shall be supported by a heavy duty turntable bearing assembly and rotate 335° via a hydraulic powered worm gear drive, raise and lower via two (2) hydraulic cylinders, and extend and retract 8′ (101.6 mm) via a single (1) hydraulic cylinder.
To increase the operators working area, the boom arm shall extend 8′ and have a minimum 26′ reach from the centerline of the collector body.
To reduce elbow wear, the boom tower design shall include an “air backed” elbow where materials can accumulate in a “T” section at the collector body inlet.
An 8″ dia. heavy-duty rubber hose shall be provided for connecting the boom to vacuum intake tubes.
Boom function shall be controlled by a 12 V DC hydraulic manifold valve which includes manual overrides for all functions.
Also included is a wireless remote control for boom functions.
The boom shall have minimum lifting capacity of 700 lbs. (318 kg) in the fully extend

Ad Reference ID: N/A

Leave a Reply

Item Location

To inquire about this ad listing, complete the form below to send a message to the ad poster.

Information about the ad poster

  • Listed by: mrenner
  • Member Since: January 25, 2010

Other items listed by mrenner

View all ads by mrenner »